Duotight Fittings

Converts a male flare fitting to suit standard beer or gas line with an 8mm outside diameter. The thread on this fitting will suit:MFL Ball Lock an...

Allows the coupling of both 8mm OD and 6.35mm OD tubing sizes using the duotight double O-Ring sealing system. No clamps necessary! We do recommend...

Splits 8mm OD beverage and gas tubing. If you need to split your gas line to dispense from multiple kegs using the same gas bottle and regulator th...

One way valve suitable for water and gas that suits 8mm OD tubing. This very handy fitting could save you your regulator and is a good investment. ...

No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting s...

Connect standard 8mm OD tubing to couplers and tap shanks. Duotight fittings are a type of push-in connector commonly used in the beverage industry...

Allows you to join two pieces of EVA tubing with an 8mm OD.  Duotight fittings are a type of push-in connector commonly used in the beverage indust...

The thread on this fitting will suit:MFL Ball Lock and Pin Lock DisconnectsOur MKIII and MK4 RegulatorsMany other home brew fittings with MFL Threa...

Splits 9.5mm OD EVA tubing. If you need to split your gas line to dispense from multiple kegs using the same gas bottle and regulator this is the p...

No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting s...

No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting s...

Replacement part for the temp twister. These bulkheads allow you to run tubing into a vessel with this part mounted in the wall of the container wh...

Allows you to connect 4mmx8mm or 5mmx8mm OD EVA tubing to 1/2" Male BSP fittings.  Duotight fittings are a type of push-in connector commonly used ...

The thread on this fitting will suit: 9.5mm OD beer/gas line (will suit 6mm hose) Use with 9.5mm OD tubing

Connects two pieces of 9.5mm OD EVA tubing at a right angle. Perfect for getting tubing around tight corners that could potentially cause kinking w...

Connects 8mm OD tubing to 8mm rigid port like those found on glycol chillers. Mainly used where a stronger connection is required on a rigid port.O...

Allows you to connect 6mm x 9.5mm OD EVA tubing to 1/2" Male BSP fittings.  Duotight fittings are a type of push-in connector commonly used in the ...

Easily connect two 8mm OD lines through a vessel wall with the ability to connect and disconnect them! No clamps necessary! We do recommend cutting...

No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting s...

Allows you to connect two 6.35mm pieces of EVA tubing or connect 6.35mm OD tubing to 6.35mm duotight tails.  Duotight fittings are a type of push-i...

Allows you to connect 6mm x 9.5mm OD EVA tubing to 5/8" Male BSP fittings.  This duotight fitting is used in situations where larger 9.5mm OD tubin...

Allows you to connect 6.35mm OD EVA tubing to 1/2" Male BSP fittings.  Duotight fittings are a type of push-in connector commonly used in the bever...

Allows you to connect 9.5mm OD tubing to a 1/2" female BSP thread. This fitting contains a 9.5mm Duotight fitting on one end and a 1/2" male BSP on...